Chemical Datasheet
PHENYLACETONITRILE, LIQUID |
|
Chemical Identifiers
![](javascript:dropDownText("sec1_help","sec1_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
The
Chemical Identifier fields
include common identification numbers, the
NFPA diamond
U.S. Department of Transportation hazard labels, and a general
description of the chemical. The information in CAMEO Chemicals comes
from a variety of
data sources.
| CAS Number | UN/NA Number | DOT Hazard Label | USCG CHRIS Code |
|---|---|---|---|
|
|
none | |
| NIOSH Pocket Guide | International Chem Safety Card | ||
| none | none | ||
NFPA 704
| Diamond | Hazard | Value | Description | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Health
|
3 | Can cause serious or permanent injury. | |||||||||
Flammability
|
1 | Must be preheated before ignition can occur. | ||||||||||
Instability
|
0 | Normally stable, even under fire conditions. | ||||||||||
Special
|
(NFPA, 2010)
General Description
A colorless oily liquid with an aromatic odor. Insoluble in water and slightly denser than water. Contact may irritate skin, eyes, and mucous membranes. May be toxic by ingestion. Used to make other chemicals.
Hazards
![](javascript:dropDownText("sec2_help","sec2_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
The
Hazard fields
include
special hazard alerts
air and water
reactions, fire hazards, health hazards, a reactivity profile, and
details about
reactive groups assignments
and
potentially incompatible absorbents.
The information in CAMEO Chemicals comes from a variety of
data sources.
Reactivity Alerts
none
Air & Water Reactions
This chemical is moisture sensitive. Insoluble in water.
Fire Hazard
When heated to decomposition, it emits very toxic fumes of cyanide and nitrogen oxides. Container may explode in heat of fire. Runoff from fire control water may give off poisonous gases. Avoid sodium hypochlorite. (EPA, 1998)
Health Hazard
Poisonous. May be fatal if inhaled, swallowed, or absorbed through skin. Contact may cause burns to skin and eyes. (EPA, 1998)
Reactivity Profile
PHENYLACETONITRILE can react with strong acids, strong bases, strong oxidizing agents and strong reducing agents. It may react vigorously with sodium hypochlorite. (NTP, 1992).
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents
No information available.
Response Recommendations
![](javascript:dropDownText("sec3_help","sec3_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
The
Response Recommendation fields
include isolation and evacuation distances, as well as recommendations for
firefighting, non-fire response, protective clothing, and first aid. The
information in CAMEO Chemicals comes from a variety of
data sources.
Isolation and Evacuation
Excerpt from ERG Guide 152 [Substances - Toxic (Combustible)]:
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2020)
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2020)
Firefighting
Keep unnecessary people away; isolate hazard area and deny entry. Stay upwind; keep out of low areas. Ventilate closed spaces before entering them. Wear positive pressure breathing apparatus and special protective clothing. Remove and isolate contaminated clothing at the site.
Small fires: dry chemical, carbon dioxide, water spray, or foam. Large fires: water spray, fog, or foam. Move container from fire area if you can do it without risk. Fight fire from maximum distance. Dike fire control water for later disposal; do not scatter the material. (EPA, 1998)
Small fires: dry chemical, carbon dioxide, water spray, or foam. Large fires: water spray, fog, or foam. Move container from fire area if you can do it without risk. Fight fire from maximum distance. Dike fire control water for later disposal; do not scatter the material. (EPA, 1998)
Non-Fire Response
Excerpt from ERG Guide 152 [Substances - Toxic (Combustible)]:
ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. Cover with plastic sheet to prevent spreading. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. DO NOT GET WATER INSIDE CONTAINERS. (ERG, 2020)
ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. Cover with plastic sheet to prevent spreading. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. DO NOT GET WATER INSIDE CONTAINERS. (ERG, 2020)
Protective Clothing
For emergency situations, wear a positive pressure, pressure-demand, full facepiece self-contained breathing apparatus (SCBA) or pressure- demand supplied air respirator with escape SCBA and a fully-encapsulating, chemical resistant suit. (EPA, 1998)
DuPont Tychem® Suit Fabrics
![](javascript:dropDownText("dupont_help","dupont_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
Tychem® Fabric Legend
| QS = Tychem 2000 SFR |
| QC = Tychem 2000 |
| SL = Tychem 4000 |
| C3 = Tychem 5000 |
| TF = Tychem 6000 |
| TP = Tychem 6000 FR |
| RC = Tychem RESPONDER® CSM |
| TK = Tychem 10000 |
| RF = Tychem 10000 FR |
Testing Details
The fabric permeation data was generated for DuPont by a third party
laboratory. Permeation data for industrial chemicals is obtained per
ASTM F739. Normalized breakthrough times (the time at which the
permeation rate exceeds 0.1 μg/cm2/min) are reported in minutes. All
chemicals have been tested between approximately 20°C and 27°C unless
otherwise stated. All chemicals have been tested at a concentration of
greater than 95% unless otherwise stated.
Chemical warfare agents (Lewisite, Sarin, Soman, Sulfur Mustard, Tabun
and VX Nerve Agent) have been tested at 22°C and 50% relative humidity
per military standard MIL-STD-282. "Breakthrough time" for chemical
warfare agents is defined as the time when the cumulative mass which
permeated through the fabric exceeds the limit in MIL-STD-282 [either
1.25 or 4.0 μg/cm2].
A Caution from DuPont
This information is based upon technical data that DuPont believes to
be reliable on the date issued. It is subject to revision as additional
knowledge and experience are gained. The information reflects
laboratory performance of fabrics, not complete garments, under
controlled conditions. It is intended for informational use by persons
having technical skill for evaluation under their specific end-use
conditions, at their own discretion and risk. It is the user's
responsibility to determine the level of toxicity and the proper
personal protective equipment needed. Anyone intending to use this
information should first verify that the garment selected is suitable
for the intended use. In many cases, seams and closures have shorter
breakthrough times and higher permeation rates than the fabric. If
fabric becomes torn,abraded or punctured, or if seams or closures fail,
or if attached gloves, visors, etc. are damaged, end user should
discontinue use of garment to avoid potential exposure to chemical.
Since conditions of use are outside our control, DuPont makes no
warranties, express or implied, including, without limitation, no
warranties of merchantability or fitness for a particular use and
assume no liability in connection with any use of this information.
This information is not intended as a license to operate under or a
recommendation to infringe any patent, trademark or technical
information of DuPont or others covering any material or its use.
| Chemical | CAS Number | State | QS | QC | SL | C3 | TF | TP | RC | TK | RF |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Benzyl cyanide | 140-29-4 | Liquid | >480 | >390 | >390 | ||||||
| Phenyl acetonitrile | 140-29-4 | Liquid | >480 | >390 | >390 |
> indicates greater than.
Special Warning from DuPont: Tychem® and Tyvek® fabrics should not be used around heat, flames, sparks or in potentially flammable or explosive environments. Only...
![](javascript:dropDownText("dupont_help2","dupont_help2_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
...Tychem® ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T
(with aluminized outer suit) garments are designed and tested to help
reduce burn injury during escape from a flash fire. Users of Tychem®
ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T (with
aluminized outer suit) garments should not knowingly enter an explosive
environment. Tychem® garments with attached socks must be worn inside
protective outer footwear and are not suitable as outer footwear. These
attached socks do not have adequate durability or slip resistance to be
worn as the outer foot covering.
(DuPont, 2023)
First Aid
Warning: Benzyl cyanide may be fatal if inhaled, swallowed, or absorbed through skin or mucous membranes. Caution is advised.
Signs and Symptoms of Acute Benzyl Cyanide Exposure: Signs and symptoms of acute exposure to benzyl cyanide may include hypertension (high blood pressure) and tachycardia (rapid heart rate), followed by hypotension (low blood pressure) and bradycardia (slow heart rate). Cherry-red or bloody mucous membranes may be noted. Cardiac arrhythmias and other cardiac abnormalities are common. Cyanosis (blue tint to the skin and mucous membranes) may be observed. Headache, vertigo (dizziness), agitation, and giddiness may be followed by combative behavior, convulsions, paralysis, protruding eyeballs, dilated and unreactive pupils, and coma. Tachypnea (rapid, shallow respirations) or hyperpnea (rapid, deep respirations) may be followed by respiratory depression. Lung hemorrhage and pulmonary edema may also occur. Benzyl cyanide is irritating to the skin, eyes, and mucous membranes. Lacrimation (tearing) and a burning sensation of the mouth and throat are common. Salivation, nausea, and vomiting may also occur.
Emergency Life-Support Procedures: Acute exposure to benzyl cyanide may require decontamination and life support for the victims. All exposed persons should be transported to a health care facility as quickly as possible. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.
Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to benzyl cyanide.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
3. RUSH to a health care facility!
4. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self- exposure to benzyl cyanide.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
3. RUSH to a health care facility!
4. Remove contaminated clothing as soon as possible.
5. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
6. Wash exposed skin areas twice with soap and water.
7. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
2. RUSH to a health care facility!
3. DO NOT induce vomiting or attempt to neutralize!
4. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
5. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
6. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults. (EPA, 1998)
Signs and Symptoms of Acute Benzyl Cyanide Exposure: Signs and symptoms of acute exposure to benzyl cyanide may include hypertension (high blood pressure) and tachycardia (rapid heart rate), followed by hypotension (low blood pressure) and bradycardia (slow heart rate). Cherry-red or bloody mucous membranes may be noted. Cardiac arrhythmias and other cardiac abnormalities are common. Cyanosis (blue tint to the skin and mucous membranes) may be observed. Headache, vertigo (dizziness), agitation, and giddiness may be followed by combative behavior, convulsions, paralysis, protruding eyeballs, dilated and unreactive pupils, and coma. Tachypnea (rapid, shallow respirations) or hyperpnea (rapid, deep respirations) may be followed by respiratory depression. Lung hemorrhage and pulmonary edema may also occur. Benzyl cyanide is irritating to the skin, eyes, and mucous membranes. Lacrimation (tearing) and a burning sensation of the mouth and throat are common. Salivation, nausea, and vomiting may also occur.
Emergency Life-Support Procedures: Acute exposure to benzyl cyanide may require decontamination and life support for the victims. All exposed persons should be transported to a health care facility as quickly as possible. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.
Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to benzyl cyanide.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
3. RUSH to a health care facility!
4. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self- exposure to benzyl cyanide.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
3. RUSH to a health care facility!
4. Remove contaminated clothing as soon as possible.
5. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
6. Wash exposed skin areas twice with soap and water.
7. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with benzyl cyanide-contaminated persons or their gastric contents can result in self-poisoning.
2. RUSH to a health care facility!
3. DO NOT induce vomiting or attempt to neutralize!
4. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
5. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
6. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults. (EPA, 1998)
Physical Properties
![](javascript:dropDownText("sec4_help","sec4_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
The
Physical Property fields
include properties such as vapor pressure and
boiling point, as well as explosive limits and
toxic exposure thresholds
The information in CAMEO Chemicals comes from a variety of
data sources.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
| Chemical Formula: |
|
Flash Point:
215°F
(NTP, 1992)
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature: data unavailable
Melting Point:
-10.8°F
(EPA, 1998)
Vapor Pressure:
1 mmHg
at 140°F
(EPA, 1998)
Vapor Density (Relative to Air): data unavailable
Specific Gravity:
1.0214
at 59°F
(EPA, 1998)
- Denser than water; will sink
Boiling Point:
451.4°F
at 760 mmHg
(EPA, 1998)
Molecular Weight:
117.14
(EPA, 1998)
Water Solubility:
less than 1 mg/mL
at 63°F
(NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: data unavailable
AEGLs (Acute Exposure Guideline Levels)
No AEGL information available.ERPGs (Emergency Response Planning Guidelines)
No ERPG information available.PACs (Protective Action Criteria)
| Chemical | PAC-1 | PAC-2 | PAC-3 |
|---|---|---|---|
| Benzyl cyanide; (Phenylacetonitrile) (140-29-4) | 0.39 mg/m3 | 4.3 mg/m3 | 15 mg/m3 |
(DOE, 2018)
Regulatory Information
![](javascript:dropDownText("sec5_help","sec5_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
The
Regulatory Information fields
include information from
the U.S. Environmental Protection Agency's Title III Consolidated List of
Lists,
the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility
Anti-Terrorism Standards,
and the U.S. Occupational Safety and Health Administration's
Process Safety Management of Highly Hazardous Chemicals Standard List
(see more about these
data sources).
EPA Consolidated List of Lists
| Regulatory Name | CAS Number/ 313 Category Code |
EPCRA 302 EHS TPQ |
EPCRA 304 EHS RQ |
CERCLA RQ | EPCRA 313 TRI |
RCRA Code |
CAA 112(r) RMP TQ |
|---|---|---|---|---|---|---|---|
| Benzyl cyanide | 140-29-4 | 500 pounds | 500 pounds |
(EPA List of Lists, 2022)
CISA Chemical Facility Anti-Terrorism Standards (CFATS)
No regulatory information available.OSHA Process Safety Management (PSM) Standard List
No regulatory information available.Alternate Chemical Names
![](javascript:dropDownText("sec6_help","sec6_help_marker","/static/images/dropdown_opened.gif","/static/images/dropdown_closed.gif"))
This section provides a listing of alternate names for this chemical,
including trade names and synonyms.
- ACETIC ACID, PHENYL-NITRILE
- ACETONITRILE, PHENYL-
- ALPHA-CYANOTOLUENE
- ALPHA-PHENYLACETONITRILE
- ALPHA-TOLUNITRILE
- BENZENEACETONITRILE
- BENZENEACETONITRILE (9CI)
- BENZYL CYANIDE
- BENZYL NITRILE
- (CYANOMETHYL)BENZENE
- OMEGA-CYANOTOLUENE
- PHENACETONITRILE
- PHENYLACETONITRILE
- PHENYLACETONITRILE, LIQUID
- 2-PHENYLACETONITRILE
- 2-PHENYLETHANENITRILE
- TOLUENE, ALPHA-CYANO
- USAF KF-21
Web site owner:
Office of Response and Restoration
,
National Ocean Service,
National Oceanic and Atmospheric Administration.
USA.gov.
CAMEO Chemicals version 3.0.0.