Chemical Datasheet
LINDANE |
![]() |
Chemical Identifiers
The
Chemical Identifier fields
include common identification numbers, the
NFPA diamond
U.S. Department of Transportation hazard labels, and a general
description of the chemical. The information in CAMEO Chemicals comes
from a variety of
data sources.
CAS Number | UN/NA Number | DOT Hazard Label | USCG CHRIS Code |
---|---|---|---|
|
|
||
NIOSH Pocket Guide | International Chem Safety Card | ||
Lindane |
NFPA 704
data unavailable
General Description
Colorless solid with a musty odor; pure material is odorless. Used as a pesticide and scabicide. (EPA, 1998)
Hazards
The
Hazard fields
include
special hazard alerts
air and water
reactions, fire hazards, health hazards, a reactivity profile, and
details about
reactive groups assignments
and
potentially incompatible absorbents.
The information in CAMEO Chemicals comes from a variety of
data sources.
Reactivity Alerts
none
Air & Water Reactions
Insoluble in water.
Fire Hazard
When heated to decomposition, this compound emits toxic fumes of chlorine, hydrochloric acid, and phosgene. (EPA, 1998)
Health Hazard
Lindane is a stimulant of the nervous system, causing violent convulsions that are rapid in onset and generally followed by death or recovery within 24 hours. The probable human oral lethal dose is 50-500 mg/kg, or between 1 teaspoon and 1 ounce for a 150-lb (70 kg) person. (EPA, 1998)
Reactivity Profile
LINDANE is incompatible with strong bases. It is incompatible with powdered metals such as iron, zinc and aluminum. It is also incompatible with oxidizing agents. It can undergo oxidation when in contact with ozone. When exposed to alkalis, this chemical undergoes dehydrochlorination. (NTP, 1992)
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents
No information available.
Response Recommendations
The
Response Recommendation fields
include isolation and evacuation distances, as well as recommendations for
firefighting, non-fire response, protective clothing, and first aid. The
information in CAMEO Chemicals comes from a variety of
data sources.
Isolation and Evacuation
Excerpt from ERG Guide 151 [Substances - Toxic (Non-Combustible)]:
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
Firefighting
Isolate hazard area and deny entry. Stay upwind and keep out of low areas. Ventilate closed spaces before entering. Wear positive pressure breathing apparatus and special protective clothing. Fight fire from maximum distance, dike fire control water for later disposal.
Use dry chemical, carbon dioxide, water spray, or foam for small fires. Use water spray, fog, or foam for large fires. Move container from fire area if this can be done without risk. Use water to keep fire-exposed containers cool. (EPA, 1998)
Use dry chemical, carbon dioxide, water spray, or foam for small fires. Use water spray, fog, or foam for large fires. Move container from fire area if this can be done without risk. Use water to keep fire-exposed containers cool. (EPA, 1998)
Non-Fire Response
Do not touch spilled material. Sweep or shovel material into a clean, dry container. Carefully collect remainder. (EPA, 1998)
Protective Clothing
Excerpt from NIOSH Pocket Guide for Lindane
:
Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.
Eyes: No recommendation is made specifying the need for eye protection.
Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.
Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.
Change: DAILY - Workers whose clothing may have become contaminated should change into uncontaminated clothing before leaving the work premises.
Provide: QUICK DRENCH - Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2024)
Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.
Eyes: No recommendation is made specifying the need for eye protection.
Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.
Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.
Change: DAILY - Workers whose clothing may have become contaminated should change into uncontaminated clothing before leaving the work premises.
Provide: QUICK DRENCH - Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2024)
DuPont Tychem® Suit Fabrics
Tychem® Fabric Legend
QS = Tychem 2000 SFR |
QC = Tychem 2000 |
SL = Tychem 4000 |
C3 = Tychem 5000 |
TF = Tychem 6000 |
TP = Tychem 6000 FR |
RC = Tychem RESPONDER® CSM |
TK = Tychem 10000 |
RF = Tychem 10000 FR |
Testing Details
The fabric permeation data was generated for DuPont by a third party
laboratory. Permeation data for industrial chemicals is obtained per
ASTM F739. Normalized breakthrough times (the time at which the
permeation rate exceeds 0.1 μg/cm2/min) are reported in minutes. All
chemicals have been tested between approximately 20°C and 27°C unless
otherwise stated. All chemicals have been tested at a concentration of
greater than 95% unless otherwise stated.
Chemical warfare agents (Lewisite, Sarin, Soman, Sulfur Mustard, Tabun
and VX Nerve Agent) have been tested at 22°C and 50% relative humidity
per military standard MIL-STD-282. "Breakthrough time" for chemical
warfare agents is defined as the time when the cumulative mass which
permeated through the fabric exceeds the limit in MIL-STD-282 [either
1.25 or 4.0 μg/cm2].
A Caution from DuPont
This information is based upon technical data that DuPont believes to
be reliable on the date issued. It is subject to revision as additional
knowledge and experience are gained. The information reflects
laboratory performance of fabrics, not complete garments, under
controlled conditions. It is intended for informational use by persons
having technical skill for evaluation under their specific end-use
conditions, at their own discretion and risk. It is the user's
responsibility to determine the level of toxicity and the proper
personal protective equipment needed. Anyone intending to use this
information should first verify that the garment selected is suitable
for the intended use. In many cases, seams and closures have shorter
breakthrough times and higher permeation rates than the fabric. If
fabric becomes torn,abraded or punctured, or if seams or closures fail,
or if attached gloves, visors, etc. are damaged, end user should
discontinue use of garment to avoid potential exposure to chemical.
Since conditions of use are outside our control, DuPont makes no
warranties, express or implied, including, without limitation, no
warranties of merchantability or fitness for a particular use and
assume no liability in connection with any use of this information.
This information is not intended as a license to operate under or a
recommendation to infringe any patent, trademark or technical
information of DuPont or others covering any material or its use.
Chemical | CAS Number | State | QS | QC | SL | C3 | TF | TP | RC | TK | RF |
---|---|---|---|---|---|---|---|---|---|---|---|
Hexachloro cyclohexane, 1,2,3,4,5,6- (sat in Acetone) | 58-89-9 | Liquid | >480 | >480 | >480 | ||||||
Hexachloro cyclohexane, 1,2,3,4,5,6- (sat in Methanol) | 58-89-9 | Liquid | >480 | ||||||||
Lindane (sat in Acetone) | 58-89-9 | Liquid | >480 | >480 | >480 | ||||||
Lindane (sat in Methanol) | 58-89-9 | Liquid | >480 |
> indicates greater than.
Special Warning from DuPont: Tychem® and Tyvek® fabrics should not be used around heat, flames, sparks or in potentially flammable or explosive environments. Only...
...Tychem® ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T
(with aluminized outer suit) garments are designed and tested to help
reduce burn injury during escape from a flash fire. Users of Tychem®
ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T (with
aluminized outer suit) garments should not knowingly enter an explosive
environment. Tychem® garments with attached socks must be worn inside
protective outer footwear and are not suitable as outer footwear. These
attached socks do not have adequate durability or slip resistance to be
worn as the outer foot covering.
(DuPont, 2024)
First Aid
Signs and Symptoms of Acute Lindane exposure: Signs and symptoms of acute exposure to lindane may be severe and include headache, dizziness, increased sensitivity to stimuli, agitation, nervousness, tremor, seizures, and coma. Convulsive episodes may alternate with periods of severe central nervous system depression. Nausea, vomiting, and diarrhea are common. Hypertension (high blood pressure), tachycardia (rapid heart rate), and cardiac arrhythmias (abnormal heart beat) may be noted. Respiratory depression may lead to respiratory arrest. Contact with the skin, eyes, and mucous membranes may result in redness and irritation. Victims often have an elevated temperature.
Emergency Life-Support Procedures: Acute exposure to lindane may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.
Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to lindane.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. Transport to a health care facility.
Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self-exposure to lindane.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not labored, administer 100% humidified oxygen or other respiratory support.
3. Remove and isolate contaminated clothing as soon as possible.
4. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
5. Wash exposed skin areas three times. Wash initially with soap and water, follow with an alcohol wash, then again with soap and water.
6. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
7. Transport to a health care facility.
Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.
2. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
3. Vomiting may be induced with syrup of Ipecac. If elapsed time since ingestion of lindane is unknown or suspected to be greater than 30 minutes, do not induce vomiting and proceed to Step 4. Ipecac should not be administered to children under 6 months of age. Warning: Ingestion of lindane may result in sudden onset of seizures or loss of consciousness. Syrup of Ipecac should be administered only if victims are alert, have an active gag reflex, and show no signs of impending seizure or coma. If ANY uncertainty exists, proceed to Step 4. The following dosages of Ipecac are recommended: children up to 1 year old, 10 mL (1/3 oz); children 1 to 12 years old, 15 mL (1/2 oz); adults, 30 mL (1 oz). Ambulate (walk) the victims and give large quantities of water. If vomiting has not occurred after 15 minutes, Ipecac may be readministered. Continue to ambulate and give water to the victims. If vomiting has not occurred within 15 minutes after second administration of Ipecac, administer activated charcoal.
4. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
5. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults.
6. Transport to a health care facility. (EPA, 1998)
Emergency Life-Support Procedures: Acute exposure to lindane may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.
Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to lindane.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. Transport to a health care facility.
Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self-exposure to lindane.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not labored, administer 100% humidified oxygen or other respiratory support.
3. Remove and isolate contaminated clothing as soon as possible.
4. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
5. Wash exposed skin areas three times. Wash initially with soap and water, follow with an alcohol wash, then again with soap and water.
6. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
7. Transport to a health care facility.
Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer 100% humidified oxygen or other respiratory support.
2. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
3. Vomiting may be induced with syrup of Ipecac. If elapsed time since ingestion of lindane is unknown or suspected to be greater than 30 minutes, do not induce vomiting and proceed to Step 4. Ipecac should not be administered to children under 6 months of age. Warning: Ingestion of lindane may result in sudden onset of seizures or loss of consciousness. Syrup of Ipecac should be administered only if victims are alert, have an active gag reflex, and show no signs of impending seizure or coma. If ANY uncertainty exists, proceed to Step 4. The following dosages of Ipecac are recommended: children up to 1 year old, 10 mL (1/3 oz); children 1 to 12 years old, 15 mL (1/2 oz); adults, 30 mL (1 oz). Ambulate (walk) the victims and give large quantities of water. If vomiting has not occurred after 15 minutes, Ipecac may be readministered. Continue to ambulate and give water to the victims. If vomiting has not occurred within 15 minutes after second administration of Ipecac, administer activated charcoal.
4. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
5. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults.
6. Transport to a health care facility. (EPA, 1998)
Physical Properties
The
Physical Property fields
include properties such as vapor pressure and
boiling point, as well as explosive limits and
toxic exposure thresholds
The information in CAMEO Chemicals comes from a variety of
data sources.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula: |
|
Flash Point: data unavailable
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature:
Not flammable
(USCG, 1999)
Melting Point:
234.5°F
(EPA, 1998)
Vapor Pressure:
9.4e-06 mmHg
at 68°F
(EPA, 1998)
Vapor Density (Relative to Air): data unavailable
Specific Gravity:
1.9
(EPA, 1998)
- Denser than water; will sink
Boiling Point:
614°F
at 760 mmHg
Decomposes
(EPA, 1998)
Molecular Weight:
290.83
(EPA, 1998)
Water Solubility:
less than 1 mg/mL
at 75°F
(NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH:
50 mg/m3
(NIOSH, 2024)
AEGLs (Acute Exposure Guideline Levels)
No AEGL information available.ERPGs (Emergency Response Planning Guidelines)
No ERPG information available.PACs (Protective Action Criteria)
Chemical | PAC-1 | PAC-2 | PAC-3 |
---|---|---|---|
Lindane; (gamma-Benzenehexachloride) (58-89-9) | 9.1 mg/m3 | 100 mg/m3 | 1000 mg/m3 |
(DOE, 2024)
Regulatory Information
The
Regulatory Information fields
include information from
the U.S. Environmental Protection Agency's Title III Consolidated List of
Lists,
the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility
Anti-Terrorism Standards,
and the U.S. Occupational Safety and Health Administration's
Process Safety Management of Highly Hazardous Chemicals Standard List
(see more about these
data sources).
EPA Consolidated List of Lists
Regulatory Name | CAS Number/ 313 Category Code |
EPCRA 302 EHS TPQ |
EPCRA 304 EHS RQ |
CERCLA RQ | EPCRA 313 TRI |
RCRA Code |
CAA 112(r) RMP TQ |
---|---|---|---|---|---|---|---|
Cyclohexane, 1,2,3,4,5,6-hexachloro-,(1.alpha.,2.alpha.,3.beta.,4.alpha.,5.alpha.,6.beta.)- | 58-89-9 | 1000/10000 pounds | 1 pound | 1 pound | X | U129 | |
Hexachlorocyclohexane (gamma isomer) | 58-89-9 | 1000/10000 pounds | 1 pound | 1 pound | X | U129 | |
Lindane | 58-89-9 | 1000/10000 pounds | 1 pound | 1 pound | 313 | U129 |
- "X" indicates that this is a second name for an EPCRA section 313 chemical already included on this consolidated list. May also indicate that the same chemical with the same CAS number appears on another list with a different chemical name.
(EPA List of Lists, 2024)
CISA Chemical Facility Anti-Terrorism Standards (CFATS)
No regulatory information available.OSHA Process Safety Management (PSM) Standard List
No regulatory information available.Alternate Chemical Names
This section provides a listing of alternate names for this chemical,
including trade names and synonyms.
- 666
- AALINDAN
- AFICIDE
- AGRISOL G-20
- AGROCIDE
- AGROCIDE 2
- AGROCIDE 6G
- AGROCIDE 7
- AGROCIDE III
- AGROCIDE WP
- AGRONEXIT
- 1-ALPHA, 2-ALPHA, 3-BETA, 4-ALPHA, 5-ALPHA, 6-BETA-HEXACHLOROCYCLOHEXANE
- 1-ALPHA,2-ALPHA,3-BETA,4-ALPHA, 5-ALPHA,6-BETA-HEXACHLOROCYCLOHEXANE
- AMEISENATOD
- AMEISENMITTEL MERCK
- APARASIN
- APHTIRIA
- APLIDAL
- ARBITEX
- ARCOTAL S
- BBH
- BEN-HEX
- BENHEXOL
- BENTOX 10
- BENZENE HEXACHLORIDE
- BENZENE HEXACHLORIDE-GAMMA-ISOMER
- BERCEMA-SPRITZ-LINDAN 50
- BEXOL
- BHC
- BHC (INSECTICIDE)
- CELANEX
- CHLORESENE
- CODECHINE
- CYCLOHEXANE, 1,2,3,4,5,6-HEXACHLORO-, GAMMA-
- CYCLOHEXANE, 1,2,3,4,5,6-HEXACHLORO-, GAMMA-ISOMER
- CYCLOHEXANE, HEXACHLORO-
- DBH
- DETMOL EXTRACT
- DETMOL-EXTRAKT
- DETOX 25
- DEVORAN
- DOL GRANULE
- DRILL TOX-SPEZIAL AGLUKON
- DRILLTOX-SPEZIAL AGLUKON
- ENT 7,796
- ENTOMOXAN
- EXAGAMA
- FENOFORM FORTE
- FORLIN
- FORST-NEXEN
- GALLOGAMA
- GAMACARBATOX
- GAMACID
- GAMACIDE
- GAMACIDE 20
- GAMAPHEX
- GAMENE
- GAMISO
- GAMMA BENZENE HEXACHLORIDE
- GAMMA ISOMER OF 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE
- GAMMA- 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE
- GAMMA- HEXACHLORANE
- GAMMA-1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE
- GAMMA-666
- GAMMA-BENZENE HEXACHLORIDE
- GAMMA-BENZOHEXACHLORIDE
- GAMMA-BHC
- GAMMA-COL
- GAMMA-HCH
- GAMMA-HEXACHLOR
- GAMMA-HEXACHLORAN
- GAMMA-HEXACHLORANE
- GAMMA-HEXACHLOROBENZENE
- GAMMA-HEXACHLOROCYCLOHEXANE
- GAMMA-LINDANE
- GAMMAHEXA
- GAMMAHEXANE
- GAMMALIN
- GAMMALIN 20
- GAMMATERR
- GAMMEX
- GAMMEXANE
- GAMMOPAZ
- GAMOLINE
- GEOBILAN
- GEOLIN G 3
- GEXANE
- HCC
- HCCH
- HCH
- HECLOTOX
- HECOLTOX
- HEXACHLORAN
- HEXACHLORANE
- HEXACHLOROCYCLOHEXANE
- HEXACHLOROCYCLOHEXANE (GAMMA ISOMER)
- 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE, ALPHA ISOMER
- HEXACHLOROCYCLOHEXANE, GAMMA ISOMER
- 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE, GAMMA ISOMER
- HEXACHLOROCYCLOHEXANE, GAMMA-ISOMER
- 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE, GAMMA-ISOMER
- 1,2,3,4,5,6-HEXACHLOROCYCLOHEXANE
- HEXACHLOROCYLOHEXANE
- 1,2,3,4,5,6-HEXACHLOROCYLOHEXANE,GAMMA-ISOMER
- HEXATIN
- HEXATOX
- HEXAVERM
- HEXICIDE
- HEXYCLAN
- HGI
- HILBEECH
- HORTEX
- HUNGARIA L 7
- HUNGARIA L7
- INEXIT
- ISOTOX
- JACUTIN
- KANODANE
- KOKOTINE
- KWELL
- LASOCHRON
- LENDINE
- LENTOX
- LIDENAL
- LINDAFOR
- LINDAGAM
- LINDAGRAIN
- LINDAGRANOX
- LINDANE
- LINDANE (ACGIH,DOT,OSHA)
- LINDANE, [SOLID]
- LINDAPOUDRE
- LINDATOX
- LINDEX
- LINDOSEP
- LINTOX
- LINTOX 3
- LINVUR
- LOREXANE
- MGLAWIK L
- MILBOL 49
- MSZYCHOL
- MSZYCOL
- NCI-C00204
- NEO-SCABICIDOL
- NEXEN FB
- NEXEN-FB
- NEXIT
- NEXIT STARK
- NEXIT-STARK
- NEXOL E
- NEXOL-E
- NICOCHLORAN
- NOVIGAM
- OMNITOX
- OVADZIAK
- OWADZIAK
- OWADZLAK
- PEDRACZAK
- PFLANZOL
- PLK
- QUELLADA
- SANG GAMMA
- SANG-GAMMA
- SILVANOL
- SPRITZ-RAPIDIN
- SPRITZLINDANE
- SPRUEHPFLANZOL
- STREUNEX
- TAP 85
- TRI-6
- VERINDAL ULTRA
- VITON