|CAS Number||UN/NA Number||DOT Hazard Label||USCG CHRIS Code|
|NIOSH Pocket Guide||International Chem Safety Card|
|Health||2||Can cause temporary incapacitation or residual injury.|
|Flammability||4||Burns readily. Rapidly or completely vaporizes at atmospheric pressure and normal ambient temperature.|
|Instability||2||Readily undergoes violent chemical changes at elevated temperatures and pressures.|
- Highly Flammable
- Peroxidizable Compound
Behavior in Fire: Vapors are heavier than air and may travel a considerable distance to a source of ignition and flash back. (USCG, 1999)
Use caution: Liquids with this reactive group classification have been known to react with the absorbents listed below. More info about absorbents, including situations to watch out for...
- Cellulose-Based Absorbents
- Mineral-Based & Clay-Based Absorbents
As an immediate precautionary measure, isolate spill or leak area for at least 50 meters (150 feet) in all directions.
LARGE SPILL: Consider initial downwind evacuation for at least 300 meters (1000 feet).
FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2016)
CAUTION: All these products have a very low flash point: Use of water spray when fighting fire may be inefficient.
SMALL FIRE: Dry chemical, CO2, water spray or alcohol-resistant foam. Do not use dry chemical extinguishers to control fires involving nitromethane (UN1261) or nitroethane (UN2842).
LARGE FIRE: Water spray, fog or alcohol-resistant foam. Do not use straight streams. Move containers from fire area if you can do it without risk.
FIRE INVOLVING TANKS OR CAR/TRAILER LOADS: Fight fire from maximum distance or use unmanned hose holders or monitor nozzles. Cool containers with flooding quantities of water until well after fire is out. Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank. ALWAYS stay away from tanks engulfed in fire. For massive fire, use unmanned hose holders or monitor nozzles; if this is impossible, withdraw from area and let fire burn. (ERG, 2016)
ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area). All equipment used when handling the product must be grounded. Do not touch or walk through spilled material. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. A vapor-suppressing foam may be used to reduce vapors. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. Use clean, non-sparking tools to collect absorbed material.
LARGE SPILL: Dike far ahead of liquid spill for later disposal. Water spray may reduce vapor, but may not prevent ignition in closed spaces. (ERG, 2016)
Eyes: Wear appropriate eye protection to prevent eye contact.
Wash skin: The worker should immediately wash the skin when it becomes contaminated.
Remove: Work clothing that becomes wet should be immediately removed due to its flammability hazard(i.e. for liquids with flash point < 100°F)
Change: No recommendation is made specifying the need for the worker to change clothing after the work shift.
Provide: Eyewash fountains should be provided in areas where there is any possibility that workers could be exposed to the substance; this is irrespective of the recommendation involving the wearing of eye protection. Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2016)
|QS = Tychem 2000 SFR|
|QC = Tychem 2000|
|SL = Tychem 4000|
|C3 = Tychem 5000|
|TF = Tychem 6000|
|TP = Tychem 6000 FR|
|BR = Tychem 9000|
|RC = Tychem RESPONDER® CSM|
|TK = Tychem 10000|
|RF = Tychem 10000 FR|
"imm." indicates immediate; having a normalized breakthrough time of 10 minutes or less.
A blank cell indicates the fabric has not been tested. The fabric may or may not offer barrier.
Special Warnings from DuPont
- Serged and bound seams are degraded by some hazardous liquid chemicals, such as strong acids, and should not be worn when these chemicals are present.
CAUTION: This information is based upon technical data that
DuPont believes to be reliable. It is subject to revision as
additional knowledge and experience are gained. DuPont makes no
guarantee of results and assumes no obligation or liability...
... in connection with this information. It is the user's responsibility to determine the level of toxicity and the proper personal protective equipment needed. The information set forth herein reflects laboratory performance of fabrics, not complete garments, under controlled conditions. It is intended for informational use by persons having technical skill for evaluation under their specific end-use conditions, at their own discretion and risk. Anyone intending to use this information should first verify that the garment selected is suitable for the intended use. In many cases, seams and closures have shorter breakthrough times and higher permeation rates than the fabric. Please contact DuPont for specific data. If fabric becomes torn, abraded or punctured, or if seams or closures fail, or if attached gloves, visors, etc. are damaged, end user should discontinue use of garment to avoid potential exposure to chemical. Since conditions of use are outside our control, we make no warranties, express or implied, including, without limitation, no warranties of merchantability or fitness for a particular use and assume no liability in connection with any use of this information. This information is not intended as a license to operate under or a recommendation to infringe any patent or technical information of DuPont or others covering any material or its use.
SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas.
INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. IMMEDIATELY call a physician and be prepared to transport the victim to a hospital even if no symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION: DO NOT INDUCE VOMITING. Volatile chemicals have a high risk of being aspirated into the victim's lungs during vomiting which increases the medical problems. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. IMMEDIATELY transport the victim to a hospital. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital.
OTHER: Since this chemical is a known or suspected carcinogen you should contact a physician for advice regarding the possible long term health effects and potential recommendation for medical monitoring. Recommendations from the physician will depend upon the specific compound, its chemical, physical and toxicity properties, the exposure level, length of exposure, and the route of exposure. (NTP, 1992)
AEGLs (Acute Exposure Guideline Levels)
|10 minutes||45 ppm||340 ppm||1100 ppm|
|30 minutes||45 ppm||340 ppm||1100 ppm|
|60 minutes||45 ppm||270 ppm||840 ppm|
|4 hours||45 ppm||170 ppm||530 ppm|
|8 hours||45 ppm||110 ppm||260 ppm|
ERPGs (Emergency Response Planning Guidelines)
|Acetaldehyde (75-07-0)||10 ppm||200 ppm||1000 ppm|
PACs (Protective Action Criteria)
|Acetaldehyde (75-07-0)||45 ppm||270 ppm||840 ppm||LEL = 40000 ppm|
EPA Consolidated List of Lists
|Regulatory Name||CAS Number/
313 Category Code
|CERCLA RQ||EPCRA 313
|Acetaldehyde||75-07-0||1000 pounds||313||U001||10000 pounds|
(EPA List of Lists, 2015)
DHS Chemical Facility Anti-Terrorism Standards (CFATS)
|Chemical of Interest||CAS Number||Min Conc||STQ||Security
|Acetaldehyde||75-07-0||1.00 %||10000 pounds||flammable|
OSHA Process Safety Management (PSM) Standard List
|Chemical Name||CAS Number||Threshold Quantity (TQ)|
Alternate Chemical Names
- ACETIC ALDEHYDE
- ETHYL ALDEHYDE