Chemical Datasheet
NITROGEN MUSTARD HYDROCHLORIDE |
![]() |
Chemical Identifiers
The
Chemical Identifier fields
include common identification numbers, the
NFPA diamond
U.S. Department of Transportation hazard labels, and a general
description of the chemical. The information in CAMEO Chemicals comes
from a variety of
data sources.
CAS Number | UN/NA Number | DOT Hazard Label | USCG CHRIS Code |
---|---|---|---|
|
|
none | |
NIOSH Pocket Guide | International Chem Safety Card | ||
none | none |
NFPA 704
data unavailable
General Description
PHYSICAL DESCRIPTION: White to off-white crystals or powder with a fishy odor. Initial pH (2% aqueous solution) 3.0-4.0. (NTP, 1992)
Hazards
The
Hazard fields
include
special hazard alerts
air and water
reactions, fire hazards, health hazards, a reactivity profile, and
details about
reactive groups assignments
and
potentially incompatible absorbents.
The information in CAMEO Chemicals comes from a variety of
data sources.
Reactivity Alerts
none
Air & Water Reactions
Hygroscopic. Water soluble.
Fire Hazard
Flash point data for this chemical are not available. It is probably combustible. (NTP, 1992)
Health Hazard
SYMPTOMS: Symptoms of exposure to this compound may include irritation of the mucous membranes, vesication, burning sensation, destruction of tissues of the skin, eyes, mucous membranes and upper respiratory tract, shortness of breath and headache. Other symptoms may include nausea, vomiting and anorexia. It can cause irritation, severe damage and burns of the eyes, and necrotizing uveitis. Exposure can lead to depression of the formed elements in the blood, weakness, diarrhea, and rarely, jaundice, alopecia, vertigo, tinnitus, diminished hearing, hemolytic anemia, various chromosomal abnormalities, agranulocytosis, thrombocytopenia (which may lead to bleeding from the gums and gastrointestinal tract, petechiae and small subcutaneous hemorrhages), immunosuppression, erythema multiforme, delayed catamenia, severe and even uncontrollable depression of the hematopoietic system, persistent pancytopenia, oligomenorrhea, temporary or permanent amenorrhea, and in males, impaired spermatogenesis, azoospermia and total germinal aplasia. Other symptoms may include leukopenia, granulocytopenia, hypoplasia of all elements of bone marrow, lymphopenia and precipitation of uric acid in kidney tubules. It can cause myelosuppression and gastrointestinal symptoms. It can also cause hemorrhagic complications, maculopapular skin eruptions, herpes zoster, and on injection, thrombophlebitis. It can also cause thrombosis on injection. Exposure can also lead to latent viral infection and menstrual irregularities in women. Necrosis has occurred following extravascular injections.
ACUTE/CHRONIC HAZARDS: This compound is highly toxic and may be fatal if inhaled, swallowed or absorbed through the skin. It is a severe irritant of the mucous membranes. It is a powerful vesicant. High concentrations are extremely destructive to tissues of the skin, eyes, mucous membranes and upper respiratory tract. There is sufficient evidence that it is an animal carcinogen. When heated to decomposition it emits toxic fumes of carbon monoxide, carbon dioxide, nitrogen oxides and hydrogen chloride gas. (NTP, 1992)
ACUTE/CHRONIC HAZARDS: This compound is highly toxic and may be fatal if inhaled, swallowed or absorbed through the skin. It is a severe irritant of the mucous membranes. It is a powerful vesicant. High concentrations are extremely destructive to tissues of the skin, eyes, mucous membranes and upper respiratory tract. There is sufficient evidence that it is an animal carcinogen. When heated to decomposition it emits toxic fumes of carbon monoxide, carbon dioxide, nitrogen oxides and hydrogen chloride gas. (NTP, 1992)
Reactivity Profile
Dry crystals are stable at temperatures up to 104°F. This chemical is incompatible with strong oxidizing agents. (NTP, 1992).
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents
Use caution: Liquids with this reactive group classification have been known to react with the absorbent listed below. More info about absorbents, including situations to watch out for...
- Mineral-Based & Clay-Based Absorbents
Response Recommendations
The
Response Recommendation fields
include isolation and evacuation distances, as well as recommendations for
firefighting, non-fire response, protective clothing, and first aid. The
information in CAMEO Chemicals comes from a variety of
data sources.
Isolation and Evacuation
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
Firefighting
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. A water spray may also be used. (NTP, 1992)
Non-Fire Response
SMALL SPILLS AND LEAKAGE: Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should store this chemical under refrigerated temperatures, and protect it from moisture. Keep it away from oxidizing materials. (NTP, 1992)
STORAGE PRECAUTIONS: You should store this chemical under refrigerated temperatures, and protect it from moisture. Keep it away from oxidizing materials. (NTP, 1992)
Protective Clothing
MINIMUM PROTECTIVE CLOTHING: If Tyvek-type disposable protective clothing is not worn during handling of this chemical, wear disposable Tyvek-type sleeves taped to your gloves.
RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with a combination filter cartridge, i.e. organic vapor/acid gas/HEPA (specific for organic vapors, HCl, acid gas, SO2 and a high efficiency particulate filter). Splash proof safety goggles should be worn while handling this chemical. Alternatively, a full face respirator, equipped as above, may be used to provide simultaneous eye and respiratory protection. (NTP, 1992)
RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with a combination filter cartridge, i.e. organic vapor/acid gas/HEPA (specific for organic vapors, HCl, acid gas, SO2 and a high efficiency particulate filter). Splash proof safety goggles should be worn while handling this chemical. Alternatively, a full face respirator, equipped as above, may be used to provide simultaneous eye and respiratory protection. (NTP, 1992)
DuPont Tychem® Suit Fabrics
No information available.
First Aid
EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas.
INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. IMMEDIATELY call a physician and be prepared to transport the victim to a hospital even if no symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION: DO NOT INDUCE VOMITING. Corrosive chemicals will destroy the membranes of the mouth, throat, and esophagus and, in addition, have a high risk of being aspirated into the victim's lungs during vomiting which increases the medical problems. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. IMMEDIATELY transport the victim to a hospital. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. Transport the victim IMMEDIATELY to a hospital.
OTHER: Since this chemical is a known or suspected carcinogen you should contact a physician for advice regarding the possible long term health effects and potential recommendation for medical monitoring. Recommendations from the physician will depend upon the specific compound, its chemical, physical and toxicity properties, the exposure level, length of exposure, and the route of exposure. (NTP, 1992)
SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas.
INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. IMMEDIATELY call a physician and be prepared to transport the victim to a hospital even if no symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION: DO NOT INDUCE VOMITING. Corrosive chemicals will destroy the membranes of the mouth, throat, and esophagus and, in addition, have a high risk of being aspirated into the victim's lungs during vomiting which increases the medical problems. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. IMMEDIATELY transport the victim to a hospital. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. Transport the victim IMMEDIATELY to a hospital.
OTHER: Since this chemical is a known or suspected carcinogen you should contact a physician for advice regarding the possible long term health effects and potential recommendation for medical monitoring. Recommendations from the physician will depend upon the specific compound, its chemical, physical and toxicity properties, the exposure level, length of exposure, and the route of exposure. (NTP, 1992)
Physical Properties
The
Physical Property fields
include properties such as vapor pressure and
boiling point, as well as explosive limits and
toxic exposure thresholds
The information in CAMEO Chemicals comes from a variety of
data sources.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula: |
|
Flash Point: data unavailable
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature: data unavailable
Melting Point:
226 to 232°F
(NTP, 1992)
Vapor Pressure: data unavailable
Vapor Density (Relative to Air): data unavailable
Specific Gravity: data unavailable
Boiling Point: data unavailable
Molecular Weight:
192.52
(NTP, 1992)
Water Solubility:
greater than or equal to 100 mg/mL
at 66°F
(NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: data unavailable
AEGLs (Acute Exposure Guideline Levels)
No AEGL information available.ERPGs (Emergency Response Planning Guidelines)
No ERPG information available.PACs (Protective Action Criteria)
Chemical | PAC-1 | PAC-2 | PAC-3 |
---|---|---|---|
Nitrogen mustard hydrochloride (55-86-7) | 0.013 mg/m3 | 0.14 mg/m3 | 0.83 mg/m3 |
(DOE, 2024)
Regulatory Information
The
Regulatory Information fields
include information from
the U.S. Environmental Protection Agency's Title III Consolidated List of
Lists,
the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility
Anti-Terrorism Standards,
and the U.S. Occupational Safety and Health Administration's
Process Safety Management of Highly Hazardous Chemicals Standard List
(see more about these
data sources).
EPA Consolidated List of Lists
No regulatory information available.CISA Chemical Facility Anti-Terrorism Standards (CFATS)
RELEASE | THEFT | SABOTAGE | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Chemical of Interest | CAS Number | Min Conc | STQ | Security Issue |
Min Conc | STQ | Security Issue |
Min Conc | STQ | Security Issue |
Nitrogen mustard hydrochloride; [Bis(2-chloroethyl)methylamine hydrochloride] | 55-86-7 | 30.00 % | 2.2 pounds | CW/CWP |
- CW/CWP = chemical weapons/chemical weapons precursors.
(CISA, 2007)
OSHA Process Safety Management (PSM) Standard List
No regulatory information available.Alternate Chemical Names
This section provides a listing of alternate names for this chemical,
including trade names and synonyms.
- ANTIMIT
- AZOTOYPERITE
- BETA,BETA'-DICHLORODIETHYL-N-METHYLAMINE HYDROCHLORIDE
- BIS(2-CHLOROETHYL)METHYLAMINE HYDROCHLORIDE
- C 6866
- CAROLYSINE
- CARYOLYSINE
- CARYOLYSINE HYDROCHLORIDE
- CHLORAMIN
- CHLORAMIN HYDROCHLORIDE
- CHLORAMINE
- CHLORETHAMINE
- CHLORETHAZINE
- CHLORMETHINE HYDROCHLORIDE
- CHLORMETHINUM
- 2-CHLORO-N-(2-CHLOROETHYL)-N-METHYLETHANAMINE HYDROCHLORIDE
- CLORAMIN
- DEMA
- DI(2-CHLOROETHYL)METHYLAMINE HYDROCHLORIDE
- DICHLOREN
- DICHLOREN HYDROCHLORIDE
- 1,5-DICHLORO-3-METHYL-3-AZAPENTANE HYDROCHLORIDE
- 2,2'-DICHLORO-N-METHYLDIETHYLAMINE HYDROCHLORIDE
- DIETHYLAMINE, 2,2'-DICHLORO-N-METHYL-, HYDROCHLORIDE
- DIMITAN
- EMBECHINE
- EMBICHIN
- EMBICHIN HYDROCHLORIDE
- EMBIKHINE
- ERASOL
- ERASOL HYDROCHLORIDE
- ERASOL-IDO
- HN2 HYDROCHLORIDE
- KLORAMIN
- MBA HYDROCHLORIDE
- MEBICHLORAMINE
- MECHLORETHAMINE HYDROCHLORIDE
- MERCHLORETHAMINE
- METHYLBIS(2-CHLOROETHYL)AMINE HYDROCHLORIDE
- METHYLBIS(BETA-CHLOROETHYL)AMINE HYDROCHLORIDE
- METHYLDI(2-CHLOROETHYL)AMINE HYDROCHLORIDE
- METHYLDI(BETA-CHLOROETHYL)AMINE HYDROCHLORIDE
- MITOXINE
- MUSTARGEN
- MUSTARGEN HYDROCHLORIDE
- MUSTINE HYDROCHLOR
- MUSTINE HYDROCHLORIDE
- N,N-BIS(2-CHLOROETHYL)METHANAMINE HYDROCHLORIDE
- N,N-BIS(2-CHLOROETHYL)METHYLAMINE HYDROCHLORIDE
- N-LOST
- N-METHYL-2,2'-DICHLORODIETHYLAMINE HYDROCHLORIDE
- N-METHYL-DI-2-CHLOROETHYLAMINE HYDROCHLORIDE
- N-METHYLBIS(2-CHLOROETHYL)AMINE HYDROCHLORIDE
- N-METHYLBIS-BETA-CHLORETHYLAMINE HYDROCHLORIDE
- NCI-C56382
- NITOL
- NITOL "TAKEDA"
- NITROGEN MUSTARD
- NITROGEN MUSTARD HYDROCHLORIDE
- NITROGRANULOGEN
- NITROGRANULOGEN HYDROCHLORIDE
- NSC 762
- NSC 762 HYDROCHLORIDE
- NSC-762 HYDROCHLORIDE
- PLIVA
- STICKSTOFFLOST
- ZAGREB