Add to MyChemicals Print Friendly Page
Chemical Datasheet

PERCHLOROMETHYL MERCAPTAN

6.1 - Poison Inhalation Hazard
Chemical Identifiers | Hazards | Response Recommendations | Physical Properties | Regulatory Information | Alternate Chemical Names

Chemical Identifiers

The Chemical Identifier fields include common identification numbers, the NFPA diamond U.S. Department of Transportation hazard labels, and a general description of the chemical. The information in CAMEO Chemicals comes from a variety of data sources.
CAS Number UN/NA Number DOT Hazard Label USCG CHRIS Code
  • 594-42-3   (PERCHLOROMETHYL MERCAPTAN)
  • Poison Inhalation Hazard
NIOSH Pocket Guide International Chem Safety Card
Perchloromethyl mercaptanexternal_link
NFPA 704
data unavailable
General Description
A yellow oily liquid with an offensive odor. Insoluble in water. Density 1.72 g / cm3. Hence sinks in water. Nonflammable but supports combustion. Very toxic by inhalation or skin absorption.

Hazards

The Hazard fields include special hazard alerts air and water reactions, fire hazards, health hazards, a reactivity profile, and details about reactive groups assignments and potentially incompatible absorbents. The information in CAMEO Chemicals comes from a variety of data sources.
Reactivity Alerts
none
Air & Water Reactions
Insoluble in water. Slowly decomposed by moisture in the air. Reacts with hot water to give carbon dioxide, hydrochloric acid and sulfur.
Fire Hazard
Very irritating vapors formed from hot material; may form phosgene gas, hydrogen chloride, and sulfur dioxide. At high temperatures this compound will decompose to carbon tetrachloride, sulfur chloride, heavy oil polymers, phosgene gas, hydrogen chloride, and sulfur dioxide. Reacts with iron or steel, evolving carbon tetrachloride. Corrosive to most metals. Reacts with water only when hot to give carbon dioxide, hydrochloric acid, and sulfur. Hazardous polymerization may not occur. (EPA, 1998)
Health Hazard
May cause death or permanent injury after short exposure to small quantities, strong irritant to eyes and skin. Inhalation may cause severe irritation of the upper respiratory tract. It also is a strong irritant to the eyes and skin. Brief exposure to lower concentrations may produce central nervous system depression and lung, liver, and heart congestion. Severe exposures may be fatal. Exposure of eyes may lead to severe conjunctivitis or corneal damage. The liquid is irritating to the skin, and may be absorbed through the skin in quantities sufficient to cause general toxic effects. Ingestion may cause damage to mucous membranes and result in pain and burning of the mouth and throat, nausea, vomiting, cramps, and diarrhea. In severe cases, tissue ulceration and CNS depression may occur. (EPA, 1998)
Reactivity Profile
PERCHLOROMETHYL MERCAPTAN is incompatible with acids, diazo and azo compounds, halocarbons, isocyanates, aldehydes, alkali metals, nitrides, hydrides, and other strong reducing agents. Reactions with these materials generate heat and in many cases hydrogen gas. Reacts readily with oxidizing agents.
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents

Use caution: Liquids with this reactive group classification have been known to react with the absorbents listed below. More info about absorbents, including situations to watch out for...

Response Recommendations

The Response Recommendation fields include isolation and evacuation distances, as well as recommendations for firefighting, non-fire response, protective clothing, and first aid. The information in CAMEO Chemicals comes from a variety of data sources.
Isolation and Evacuation
Excerpt from ERG Guide 157 [Substances - Toxic and/or Corrosive (Non-Combustible / Water-Sensitive)]:

IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

SPILL: See ERG Table 1 - Initial Isolation and Protective Action Distances on the UN/NA 1670 datasheet.

FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
Firefighting
Fight fire from maximum distance. Dike fire control water for later disposal; do not scatter the material. Positive pressure breathing apparatus and special protective clothing should be worn.

This compound is neither flammable nor a serious fire hazard, although it will support combustion. Fight small fires with dry chemical, carbon dioxide, water spray, or foam, and large fires with water spray, fog, or foam. Move containers containing this compound away from fire area if possible. (EPA, 1998)
Non-Fire Response
Excerpt from ERG Guide 157 [Substances - Toxic and/or Corrosive (Non-Combustible / Water-Sensitive)]:

ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. All equipment used when handling the product must be grounded. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. A vapor-suppressing foam may be used to reduce vapors. DO NOT GET WATER INSIDE CONTAINERS. Use water spray to reduce vapors or divert vapor cloud drift. Avoid allowing water runoff to contact spilled material. Prevent entry into waterways, sewers, basements or confined areas.

SMALL SPILL: Cover with DRY earth, DRY sand or other non-combustible material followed with plastic sheet to minimize spreading or contact with rain. Use clean, non-sparking tools to collect material and place it into loosely covered plastic containers for later disposal. (ERG, 2024)
Protective Clothing
Excerpt from NIOSH Pocket Guide for Perchloromethyl mercaptanexternal link:

Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.

Eyes: PREVENT EYE CONTACT - Wear appropriate eye protection to prevent eye contact.

Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.

Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.

Change: No recommendation is made specifying the need for the worker to change clothing after the workshift. (NIOSH, 2024)
DuPont Tychem® Suit Fabrics
No information available.
First Aid
Signs and Symptoms of Acute Perchloromethylmercaptan Exposure: Signs and symptoms of acute exposure to perchloromethylmercaptan may lead to liver, heart, and kidney damage. Respiratory effects include coughing, dyspnea (shortness of breath), painful breathing, and lung congestion. Tachycardia (rapid heart rate) is often observed. Nausea, vomiting, abdominal cramping, and diarrhea may also occur. Contact with perchloromethylmercaptan may result in severe dermatitis (red, inflamed skin), conjunctivitis (red, inflamed eyes), and burns with ulceration and severe pain.

Emergency Life-Support Procedures: Acute exposure to perchloromethylmercaptan may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.

Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to perchloromethylmercaptan.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. Transport to a health care facility.

Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self- exposure to perchloromethylmercaptan.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
3. Remove contaminated clothing as soon as possible.
4. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
5. THOROUGHLY wash exposed skin areas with soap and water.
6. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
7. Transport to a health care facility.

Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
2. DO NOT induce vomiting!
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. Give the victims water or milk: children up to 1 year old, 125 mL (4 oz or 1/2 cup); children 1 to 12 years old, 200 mL (6 oz or 3/4 cup); adults, 250 mL (8 oz or 1 cup). Water or milk should be given only if victims are conscious and alert.
5. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
6. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults.
7. Transport to a health care facility. (EPA, 1998)

Physical Properties

The Physical Property fields include properties such as vapor pressure and boiling point, as well as explosive limits and toxic exposure thresholds The information in CAMEO Chemicals comes from a variety of data sources.

Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula:
  • CCl4S
Flash Point: data unavailable
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature: data unavailable
Melting Point: data unavailable
Vapor Pressure: 25 mmHg at 123.8°F (EPA, 1998)
Vapor Density (Relative to Air): 6.414 (EPA, 1998) - Heavier than air; will sink
Specific Gravity: 1.6947 at 68°F (EPA, 1998) - Denser than water; will sink
Boiling Point: 297 to 298°F at 760 mmHg (EPA, 1998)
Molecular Weight: 185.87 (EPA, 1998)
Water Solubility: less than 1 mg/mL at 70°F (NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: 10 ppm (NIOSH, 2024)

AEGLs (Acute Exposure Guideline Levels)

Final AEGLs for Perchloromethyl mercaptan (594-42-3)
Exposure Period AEGL-1 AEGL-2 AEGL-3
10 minutes 0.013 ppm 0.53 ppm 1.6 ppm
30 minutes 0.013 ppm 0.37 ppm 1.1 ppm
60 minutes 0.013 ppm 0.3 ppm 0.9 ppm
4 hours 0.013 ppm 0.077 ppm 0.23 ppm
8 hours 0.013 ppm 0.037 ppm 0.11 ppm
Level of Distinct Odor Awareness = 0.016 ppm
(NAC/NRC, 2024)

ERPGs (Emergency Response Planning Guidelines)

No ERPG information available.

PACs (Protective Action Criteria)

Chemical PAC-1 PAC-2 PAC-3
Perchloromethyl mercaptan (594-42-3) 0.013 ppm 0.3 ppm 0.9 ppm
(DOE, 2024)

Regulatory Information

The Regulatory Information fields include information from the U.S. Environmental Protection Agency's Title III Consolidated List of Lists, the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility Anti-Terrorism Standards, and the U.S. Occupational Safety and Health Administration's Process Safety Management of Highly Hazardous Chemicals Standard List (see more about these data sources).

EPA Consolidated List of Lists

Regulatory Name CAS Number/
313 Category Code
EPCRA 302
EHS TPQ
EPCRA 304
EHS RQ
CERCLA RQ EPCRA 313
TRI
RCRA
Code
CAA 112(r)
RMP TQ
Methanesulfenyl chloride, trichloro- 594-42-3 500 pounds 100 pounds 100 pounds X 10000 pounds
Perchloromethyl mercaptan 594-42-3 500 pounds 100 pounds 100 pounds 313 10000 pounds
Trichloromethanesulfenyl chloride 594-42-3 500 pounds 100 pounds 100 pounds X 10000 pounds

(EPA List of Lists, 2024)

CISA Chemical Facility Anti-Terrorism Standards (CFATS)

RELEASE THEFT SABOTAGE
Chemical of Interest CAS Number Min Conc STQ Security
Issue
Min Conc STQ Security
Issue
Min Conc STQ Security
Issue
Perchloromethylmercaptan; [Methanesulfenyl chloride, trichloro-] 594-42-3 1.00 % 10000 pounds toxic

(CISA, 2007)

OSHA Process Safety Management (PSM) Standard List

Chemical Name CAS Number Threshold Quantity (TQ)
Perchloromethyl Mercaptan 594-42-3 150 pounds

(OSHA, 2019)

Alternate Chemical Names

This section provides a listing of alternate names for this chemical, including trade names and synonyms.