FORMALDEHYDE, SOLUTIONS (FORMALIN) (CORROSIVE)

Diamond	Hazard	Value	Description
2 3 0	Health	3	Can cause serious or permanent injury.
	Flammability	2	Must be moderately heated or exposed to relatively high ambient temperatures before ignition can occur.
	Instability	0	Normally stable, even under fire conditions.
	Special

A colorless liquid with a pungent irritating odor. Contains 37-50% formaldehyde by mass and varying amounts of methanol, added to prevent precipitation of formaldehyde polymers (formaldehyde exists in solution as CH2(OH)2 and its polymers HO(CH2O)xH where x averages about three). Formalin free of methanol is also shipped but must be kept warm (about 30°C (86°F)) to prevent polymerization. Pure formaldehyde, a gas, is not handled commercially because it tends to polymerize exothermally and may ignite. Vapor from formalin solution is flammable and an explosion hazard when exposed to flame or heat. Skin and eye irritant. Confirmed carcinogen.

• Polymerizable

The solution gives up formaldehyde vapors readily. These vapors are flammable over a wide vapor-air concentration range.

Excerpt from 153 [Substances - Toxic and/or Corrosive (Combustible)]:

Combustible material: may burn but does not ignite readily. When heated, vapors may form explosive mixtures with air: indoors, outdoors and sewers explosion hazards. Those substances designated with a (P) may polymerize explosively when heated or involved in a fire. Contact with metals may evolve flammable hydrogen gas. Containers may explode when heated. Runoff may pollute waterways. Substance may be transported in a molten form. (ERG, 2020)

Excerpt from 153 [Substances - Toxic and/or Corrosive (Combustible)]:

TOXIC; inhalation, ingestion or skin contact with material may cause severe injury or death. Contact with molten substance may cause severe burns to skin and eyes. Avoid any skin contact. Effects of contact or inhalation may be delayed. Fire may produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause environmental contamination. (ERG, 2020)

FORMALDEHYDE SOLUTION reacts violently with strong oxidizers (hydrogen peroxide, performic acid, perchloric acid in the presence of aniline, potassium permanganate, nitromethane). Reacts with bases (sodium hydroxide, potassium hydroxide, ammonia), and with nitrogen dioxide (explosive reaction around 180°C). Reacts with hydrochloric acid to form highly toxic bis(chloromethyl) ether. Polymerization reaction with phenol may develop sudden destructive pressure [Bretherick, 5th ed., 1995, p.168].

• Aldehydes
• Polymerizable Compounds

Use caution: Liquids with this reactive group classification have been known to react with the absorbents listed below.

• Cellulose-Based Absorbents
• Mineral-Based & Clay-Based Absorbents
• Dirt/Earth

Excerpt from 153 [Substances - Toxic and/or Corrosive (Combustible)]:

IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.

FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2020)

Excerpt from 153 [Substances - Toxic and/or Corrosive (Combustible)]:

SMALL FIRE: Dry chemical, CO2 or water spray.

LARGE FIRE: Dry chemical, CO2, alcohol-resistant foam or water spray. If it can be done safely, move undamaged containers away from the area around the fire. Dike runoff from fire control for later disposal.

FIRE INVOLVING TANKS OR CAR/TRAILER LOADS: Fight fire from maximum distance or use unmanned master stream devices or monitor nozzles. Do not get water inside containers. Cool containers with flooding quantities of water until well after fire is out. Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank. ALWAYS stay away from tanks engulfed in fire. (ERG, 2020)

Excerpt from 153 [Substances - Toxic and/or Corrosive (Combustible)]:

ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. DO NOT GET WATER INSIDE CONTAINERS. (ERG, 2020)

Excerpt from NIOSH Pocket Guide for Formalin (as formaldehyde):

Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.

Eyes: PREVENT EYE CONTACT - Wear appropriate eye protection to prevent eye contact.

Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.

Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.

Change: No recommendation is made specifying the need for the worker to change clothing after the workshift.

Provide:
• EYEWASH - Eyewash fountains should be provided in areas where there is any possibility that workers could be exposed to the substances; this is irrespective of the recommendation involving the wearing of eye protection.
• QUICK DRENCH - Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2023)

Normalized Breakthrough Times (in Minutes)

Chemical	CAS Number	State	QS	QC	SL	C3	TF	TP	RC	TK	RF
Formaldehyde (100 ppm)	50-00-0	Vapor							>480	>480	>480
Formaldehyde (37%)	50-00-0	Liquid			>480	>480	>480	>480
Formalin (100 ppm)	50-00-0	Vapor							>480	>480	>480
Formalin (3.7%, 1-1.5% Methanol)	50-00-0	Liquid		>480
Formalin (37% (10-15% Methanol))	50-00-0	Liquid		imm	>480	>480	>480	>480	>480	>480	>480
Formalin (37%)	50-00-0	Liquid			>480	>480	>480	>480

Special Warning from DuPont: Tychem® and Tyvek® fabrics should not be used around heat, flames, sparks or in potentially flammable or explosive environments. Only...

(DuPont, 2023)

Excerpt from NIOSH Pocket Guide for Formalin (as formaldehyde):

Eye: IRRIGATE IMMEDIATELY - If this chemical contacts the eyes, immediately wash (irrigate) the eyes with large amounts of water, occasionally lifting the lower and upper lids. Get medical attention immediately.

Skin: WATER FLUSH PROMPTLY - If this chemical contacts the skin, flush the contaminated skin with water promptly. If this chemical penetrates the clothing, immediately remove the clothing and flush the skin with water promptly. If irritation persists after washing, get medical attention.

Breathing: RESPIRATORY SUPPORT - If a person breathes large amounts of this chemical, move the exposed person to fresh air at once. If breathing has stopped, perform artificial respiration. Keep the affected person warm and at rest. Get medical attention as soon as possible.

Swallow: MEDICAL ATTENTION IMMEDIATELY - If this chemical has been swallowed, get medical attention immediately. (NIOSH, 2023)

• BFV
• F-GEN
• FANNOFORM
• FLOGUARD 1015
• FM 282
• FORMALDEHYDE (SOLUTION)
• FORMALDEHYDE SOLUTION
• FORMALDEHYDE, SOLUTIONS (FORMALIN) (CORROSIVE)
• FORMALIN
• FORMALIN (AS FORMALDEHYDE)
• FORMALIN SOLUTION
• FORMALITH
• FORMIC ALDEHYDE
• FORMIC ALDEHYDE SOLUTION
• FORMOL
• FYDE
• LYSOFORM
• METHALDEHYDE
• METHANAL
• METHANAL SOLUTION
• METHYL ALDEHYDE
• METHYLENE OXIDE
• MORBICID
• OXOMETHANE
• OXYMETHYLENE
• OXYMETHYLENE SOLUTION
• PARAFORM
• SUPERLYSOFORM